- 关 键 词:
通常我们使用show interface命令来查看接口的信息,如show interface gig 1/0或者show int pos 2/0等来分别查看路由器上千兆以太接口和POS接口的端口信息。
查看以太网接口信息,在7507上使用命令为: show interfaces fastethernet [slot/port-adapter/port] Fast Ethernet1/0/0 is up, line protocol is up Hardware is TSWITCH, address is 00e0.f7a4.5130 (bia 00e0.f7a4.5130) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) Half-duplex, 100BaseTX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:05:30, output 00:00:00, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 312 packets input, 18370 bytes, 0 no buffer Received 216 broadcasts, 0 runts, 0 giants, 0 throttles 3 input errors, 0 CRC, 0 frame, 0 overrun, 3 ignored, 0 abort 0 input packets with dribble condition detected 15490 packets output, 1555780 bytes, 0 underruns 2 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 2 output buffer failures, 0 output buffers swapped out
POS2/0/0 is up, line protocol is up Hardware is cyBus Packet over Sonet Description: PRI-T1 net to zippy (4K) to Pac-Bell Internet address is 10.1.1.1/27 MTU 4470 bytes, BW 1000 Kbit, DLY 40000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (3 sec) Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 00:23:09 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 1 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 1046 packets input, 54437 bytes, 0 no buffer Received 485 broadcasts, 0 runts, 0 giants, 0 parity 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 4013 packets output, 1357412 bytes, 0 underruns 0 output errors, 0 applique, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions
查看POS接口信息,在7507上使用命令为: show interfaces pos [slot/port-adapter/port]
1、下例给出了在7507上查看第1槽位上第1个PA上的第1个快速以太网接口的接口配置信息:
Router# show interfaces fastethernet 1/0/0
2、下例给出了在7507上查看第2槽位上第1个PA上的第1个快速以太网接口的接口配置信息:
Router# show interfaces pos 2/0/0
【相 关 文 章】
- 路由器配置 (2448篇文章)
- 交换机与路由器密码恢复 (4040篇文章)
- 路由故障处理 (2479篇文章)
- 路由安全配置 (11829篇文章)
- Cisco路由器配置手册 (4831篇文章)
- 无线宽带路由器 (3675篇文章)
- 网络故障手册 (13166篇文章)
- 路由故障处理 (97篇文章)
- 路由故障处理经验篇 (27篇文章)
- 其他常见路由器故障处理 (74篇文章)
- 教教你全面认识桥接、交换和路由 (34次浏览)
- 教你几招 路由器常见故障解决方法集锦 (25次浏览)
- 推荐:防火墙路由配置错误分析排除 (13次浏览)
- 永恒的焦点 提高企业路由器性能技术详解 (8次浏览)
- 技巧:如何让路由器摆脱安全困扰 (2次浏览)
- Cisco Catalyst 2918 Cisco IOS Release 12.2( (0次浏览)
- 新一代企业网接入路由器 (0次浏览)
- Cisco IOS技术白皮书 (0次浏览)
- cisco IOS软件简介 (0次浏览)
- Cisco IOS特性介绍 (0次浏览)
- 华为路由器静态路由配置命令详解 04-24
- 华为路由器防火墙配置命令 04-24
- 利用EtherChannel免费增加带宽 04-23
- Cisco IOS技术白皮书 04-21
- cisco IOS软件简介 04-21
- Cisco IOS特性介绍 04-21
- 新一代企业网接入路由器 04-19
- Cisco Catalyst 2918 Cisco IOS Release 12.2(44)S 04-17
- 永恒的焦点 提高企业路由器性能技术详解 04-16
- 教教你全面认识桥接、交换和路由 04-16
